A bathtub's back wall will often have a seam between the tub flange & the backerboard. This area is where caulk can be applied to seal it. But, there are some areas that cannot be sealed and might need to repaired. If you're installing a new tub surround over this area, make sure to follow the proper procedures to prevent damage to the drywall.
Make sure the back wall of the tub is level. Before you install the tub surround, remove the old one. This can be done using a prybar, or a tool like a hammer. You should also wear protective gear.
You can choose to install a tub surround made of wood, concrete, or tile, depending on your specific needs. There are many styles and colors available for these surrounds. Most common are plastic or acrylic panels. Each type has its specific installation instructions. Some kits come with only one back panel while others have two. For a lower cost, you might consider purchasing a surround that is only one piece.
Once the surround is removed, it's time to take out the corners. Next, measure the new surround and determine its dimensions. You need the correct adhesive to make sure it sticks. Adhesive will need to be applied to more than one section at a time, so allow plenty of time for it to dry.
Once you are ready to apply the adhesive mark the right and left sides of your wall as well as the top and bottom corners of the surround. This will give you a visual reference point for where to apply the adhesive. Make sure you cut the adhesive lines precisely. Masking tape can be used for making the lines visible.
Next, place the back piece of the surround against the wall and adjust the back to be flush. Be sure that the back is level with the drywall. If your back is uneven, you will need to use extra adhesive to fill the gap. It is important to allow the adhesive to dry for at least 24 hrs after you apply it.
Now it's time to put the tub surround back wall in place. This is the most straightforward part. To ensure it stays in place, it is a good idea for a friend to hold it. You can also place a level on the surface to help guide the installation.
After that, attach the flanges onto the studs. Fasteners should be driven through slightly oversized predrilled holes. For added support, add a few 2x4 nailers. They should be anchored to the drywall, but not nailed directly to the wall framing.
Before you start tiling you'll need to put on the appropriate vapor barrier. The vapor barrier is a thick, plastic sheet that protects walls from moisture. You will also need primer and paint. There are many kinds of glue to choose from, so make sure to read the directions carefully.
FAQ
How can I prevent being scammed when renovating my house
You can avoid being ripped off by knowing exactly what you are getting. Before signing any contract, read through the fine print carefully. Don't sign any contracts that aren't complete. Always request copies of signed contracts.
What should I do first when renovating my house?
Cleaning out clutter inside and out is the first step to fixing up a house. Next, you will need to eliminate mold, repair or replace any damaged walls, repaint your entire interior, and fix any leaky pipes. Next, clean the exterior surfaces and paint.
Is it better to hire either a general or subcontractor?
It is more expensive to hire a general contractor than to subcontract. General contractors often have many employees and charge clients high labor costs. A subcontractor on the other side only employs one person, so he/she charges less per-hour.
How much does it cost for a house to be renovated?
Renovations usually cost between $5,000 and $50,000. Most homeowners spend around $10,000 to $20,000 on renovations.
What should I look for when buying a home?
Be sure to have enough money in reserve for closing costs before you purchase a new home. Refinancing your mortgage might be an option if you don’t have enough cash.
Statistics
- Most lenders will lend you up to 75% or 80% of the appraised value of your home, but some will go higher. (kiplinger.com)
- ‘The potential added value of a loft conversion, which could create an extra bedroom and ensuite, could be as much as 20 per cent and 15 per cent for a garage conversion.' (realhomes.com)
- Design-builders may ask for a down payment of up to 25% or 33% of the job cost, says the NARI. (kiplinger.com)
- The average fixed rate for a home-equity loan was recently 5.27%, and the average variable rate for a HELOC was 5.49%, according to Bankrate.com. (kiplinger.com)
- According to the National Association of the Remodeling Industry's 2019 remodeling impact report , realtors estimate that homeowners can recover 59% of the cost of a complete kitchen renovation if they sell their home. (bhg.com)
External Links
How To
How do I plan a whole house remodel?
It takes careful planning and research to plan a complete house remodel. Before you start your project, there are many factors to consider. It is important to determine what type of home improvements you are looking to make. There are many categories that you could choose from: kitchen, bathroom or bedroom; living room or dining room. Once you have decided which category you wish to work in, you will need to determine how much money you have to spend on your project. If you have never worked on homes, it is best to budget at most $5,000 per room. If you have some previous experience, you may be capable of getting away with a lower amount.
Once you've determined the amount of money you can spend, you need to decide how large a job you want. For example, if you only have enough money for a small kitchen remodel, you won't be able to add a new flooring surface, install a new countertop, or even paint the walls. However, if enough money is available to complete a kitchen renovation, you should be able handle most things.
Next, find a contractor that specializes in the project you are interested in. This way, you'll be guaranteed quality results and you'll save yourself a lot of headaches later on down the road. After finding a good contractor, you should start gathering materials and supplies. You may need to purchase everything from scratch depending on the size and scope of your project. There are many stores that offer pre-made products so it shouldn't be difficult to find what you need.
After you've gathered all the supplies you need, it's time to begin making plans. Begin by sketching out a rough plan of where furniture and appliances will be placed. Next, design the layout of your rooms. Make sure that you leave space for plumbing and electrical outlets. Also, try to put the most used areas near the front door so that visitors can easily access them. Finally, you'll finish your design by deciding on colors and finishes. Keep your designs simple and in neutral tones to save money.
Once you have completed your plan, it is time to begin building. It's important that you check the codes in your area before you start construction. Some cities require permits while others allow homeowners to build without one. To begin construction you will first need to take down all walls and floors. You will then lay plywood sheets to protect your new flooring. Next, you will nail or screw together pieces wood to create the frame for your cabinets. Finally, attach doors and windows.
There are some final touches that you will need to make after you are done. For example, you'll probably want to cover exposed pipes and wires. This can be done with plastic sheeting and tape. Also, you will need to hang mirrors or pictures. Just remember to keep your work area clean and tidy at all times.
These steps will ensure that you have a beautiful and functional home, which will save you tons of money. Now that you know how to plan a whole house remodeling project, you can go ahead and get started!